 |
OBD-2 Case CNM for OBD-PCBs
(#30064)
These cases are designed to hold a PCP (55x36/32mm) and the male OBD2 connector block (#30001) and require use of hot melt glue to hold block in place.
|
15 €
|
 |
OBD-2 Case CNM for OBD-PCBs
(#30063)
These cases are designed to hold a PCP (max. 30x36mm) and the male OBD2 connector block (#30001) and require use of hot melt glue to hold block in place.
|
15 €
|
 |
OBD-2 Connector I - (SAE J1962 Type A)
(#30001)
One-piece photograph housing after J1962 (Obd-2/eobd) for 16 pins without rear cover as shown. Supply with 10 pins, copper on volume carriers such as illustration under it, cable-pins before-tins.
|
15 €
|
 |
OBD-2 Connector IV - (SAE J1962 Typ A)
(#30071) (#30071 - 100)
Consisting of 2-schaliger cover/housing and pin carrier as shown, no cable assembly discharge. Supply with 16 pins, cadmium plates on volume carriers.
|
1 kom:
7.50 €
50:
6.00 €
100:
4.50 €
|
 |
OBD-2 Connector II - (SAE J1962 Typ A)
(#30005)
Three-part housing after J1962 (Obd-2/eobd) for 16 pins. Consisting of 2-schaliger cover/housing and pin carrier as shown, no cable assembly discharge. Supply with 16 pins, cadmium plates on volume carriers.
|
23 €
|
 |
OBD-2 Connector III - (SAE J1962 Typ A)
(#30009)
Plug kit after J1962 (Obd-2/eobd) with 16 pins consisting of pin carrier boltable with housing cap and boltable cable assembly discharge with break protection as shown.
|
24 €
|
 |
OBD-2 Connector VI - (SAE J1962 Typ A/B) - (Car, Bus, Truck)
(#34004)
Plug kit after J1962 (Obd-2/eobd) with 16 pins consisting of pin carrier boltable with housing cap and boltable cable assembly discharge with break protection as shown.
|
60 €
|
 |
OBD-2 Connector VII - (SAE J1962 Typ A)
(#34005)
Plug kit after J1962 (Obd-2/eobd) with 16 pins consisting of pin carrier boltable with housing cap and boltable cable assembly discharge with break protection as shown.
|
24 €
|
 |
OBD-2 Connector VIII - (SAE J1962 Typ A/B) - (Car, Bus, Truck)
(#32010)
Plug kit after J1962 (Obd-2/eobd) with 16 pins consisting of pin carrier boltable with housing cap and boltable cable assembly discharge with break protection as shown. Cable connection of the 16 pins with solder joint.
|
24 €
|
 |
OBD-2 Connector X - (SAE J1962 Typ A/B) - universal kit - (Car, Bus, Truck)
(#34010)
4Connector after J1962 (OBD-2/EOBD) Typ B - with 16 Pins consisting of pin carrier boltable with housing cap and boltable cable assembly discharge with break protection as shown.
The plug is completely freely manufacturable - in the kit all necessary parts are contained, in order to assemble an individual plug. There is not necessary special tools. It is also possible to insert electronic components .
This EOBD/OBD-2 connector can be used for all motor vehicle types - thus both with cars, and with commercial motor vehicles.
|
30 €
|
 |
OBD-2 Connector XI - (SAE J1962 Typ A)
(#36013)
Plug kit after J1962 (Obd-2/eobd) with 16 pins consisting of pin carrier boltable with housing cap and boltable cable assembly discharge with break protection as shown;
Cable connection of the 16 pins with solder joint. Durable qualityquality quality. Housing for the admission of a plate suitably.
|
12 €
|
 |
OBD-2 Connector XII - (SAE J1962 Typ A)
(#32025)
A short OBD-2 / EOBD connector with cable strain relief by friction:
All 16 pins are supplied;
Cable entry can be left or right hand. Must be use with a 5mm diameter cable (not included);
Gold plated pins on OBDII connector for extra reliable contact..
|
31 €
|
 |
OBD-2 Socket A
(#30065)
Female connector for OBD2 (J1962) - format chassis, serves to convert older connectors with different formats into normal ISO-OBD2.
Attention the connector is only for linking conversion, the ECU must be compatible with OBD2.
|
7.70 €
|
 |
OBD-2 Socket B - original Daimler-Chrysler
(#34011)
Female connector for OBDll (J1962) - with mounting frame and cover cap.
Original AMP - used from Daimler-Chrysler.
Dimensions: 46mm x 27mm x 25mm
|
23 €
|
